Search

Refine Results
International Classification for Standards (ICS) code
Source
Standards Development Organization (SDO) code
Language
Status
National Standards of Canada (NSC) code
Period range

From

To

Displaying 171191 - 171200 of 171218
Industrial tyres and rims — Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims w...
This document specifies the load ratings of the metric series of pneumatic tyres primarily intended for industrial vehicles for use on prepared surfaces. ISO 3739-1 deals with designation, dimensions and marking; ISO 3739-3 deals with rim contours for these tyres.
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
83.160.99
Industrial tyres and rims — Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims w...
This document specifies the main requirements of the metric series of pneumatic tyres primarily intended for industrial vehicles, including designations, dimensions and markings. The tyres are based on the following parameters: —    speeds not exceeding 50 km/h; —    use on 5° tapered or flat base rims. The conversion of code-designated industrial tyres into metric-designated tyres is outside the…
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
83.160.99
Health informatics — Categorial structures for representation of acupuncture — Part 1: Acupuncture p...
ISO/TS 16843-1:2016 specifies the categorial structure within the subject field of acupuncture by defining a set of domain constraints of sanctioned characteristics each composed of a semantic link and an applicable characterizing category in order to represent the concept of acupuncture point. ISO/TS 16843-1:2016 describes sanctioned characteristics with semantic links and characterizing…
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
35.240.80
Reciprocating internal combustion engine driven alternating current generating sets — Part 13: Safet...
ISO 8528-13:2016 specifies the safety requirements for reciprocating internal combustion (RIC) engine driven generating sets up to 1 000 V consisting of an RIC engine, an alternating current (AC) generator including the additional equipment required for operating, e.g. controlgear, switchgear, auxiliary equipment. It is applicable to generating sets for land and marine use (domestic, recreational…
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
27.020; 29.160.40
Petroleum products and lubricants --Determination of roll stability of lubricating grease — Part 1: ...
This document specifies a method for evaluating the change of consistency, as measured by cone penetration, of lubricating grease when worked in the roll stability test apparatus. The method only applies to greases with cone penetration in the range 175 1/10 mm to 385 1/10 mm as measured using ISO 2137.
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
75.100
Petroleum products and lubricants --Determination of roll stability of lubricating grease — Part 2: ...
This document specifies a method for evaluating the change of consistency, as measured by cone penetration, of lubricating grease when worked in the roll stability test apparatus, in presence of water. The method only applies to greases with cone penetration in the range 175 1/10 mm to 385 1/10 mm as measured using ISO 2137.
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
75.100
Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 12100:2010 specifies basic terminology, principles and a methodology for achieving safety in the design of machinery. It specifies principles of risk assessment and risk reduction to help designers in achieving this objective. These principles are based on knowledge and experience of the design, use, incidents, accidents and risks associated with machinery. Procedures are described for…
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
13.110
Building information models — Information delivery manual — Part 2: Interaction framework
ISO 29481-2:2012 specifies a methodology and format for describing ?coordination acts' between actors in a building construction project during all life cycle stages. It therefore specifies a methodology that describes an interaction framework, an appropriate way to map responsibilities and interactions that provides a process context for information flow, a format in which the interaction…
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
35.240.67
Information technology — Cloud computing — Service level agreement (SLA) framework — Part 3: Core co...
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
35.210
Welding — Grouping system for metallic materials
This document specifies a uniform system for grouping materials for welding purposes. It can also be applied for other purposes, such as heat treatment, forming and non-destructive testing.
Publisher :
ISO
Status :
Draft
Published Date :
1969-12-30
ICS Code(s) :
25.160.01