Methods of Testing Petroleum and Associated Products
Chlorides in Glycol (Qualitative Detection)
1. SCOPE
1.1 This method describes the qualitative detection of chlorides in
glycol-based deicing-defrosting fluids.
1.2 The testing and evaluation of a product against this method may require
the use of materials and/or equipment that could be hazardous. This
document does not purport to address all the safety aspects associated
with its use.…
Methods of Testing Petroleum and Associated Products
Water Wash Resistance and Sea Water Corrosion ...
1. SCOPE
1.1 This method is used to assess the ability of a grease to maintain a
continuous film, and to prevent corrosion of steel under the conditions
of the test.
1.2 The testing and evaluation of a product against this method may
require the use of materials and/or equipment that could be hazardous.
This document does not purport to address…
Methods of Sampling and Testing Waxes and Polishes
Performance Characteristics of Liquid Metal Polis...
1. SCOPe
1.1 This method evaluates the polishing properties of liquid metal polishes
by comparing their performance characteristics with those of a standard
polish.
1.2 The testing and evaluation of a product against this method may require
the use of materials and/or equipment that could be hazardous. This
document does not purport to address all the…
Methods of Sampling and Testing Waxes and Polishes
Drop Melting Point of Petroleum Wax Including Pe...
1. Scope
1.1 This test method covers the determination of the drop melting point of
petroleum wax. It is used primarily for petrolatums and other microcrystalline
was.
NOTE 1 - Additional methods used for petroleum waxes are Test Method D 87 and
Test Method D 938. Results obtained may differ, depending on the method used.
For pharmaceutical petrolatum, Test Method D 127 usually is…
Methods of Testing Petroleum and Associated Products
1,2-Glycols in Glycol Mixtures
1. SCOPE
1.1 This method is used to determine the total concentration of 1,2-glycols
in deicing-defrosting fluid concentrates.
1.2 The testing and evaluation of a product against this method may require
the use of materials and/or equipment that could be hazardous. This
document does not purport to address all the safety aspects associated
with…
Methods of Sampling and Testing Waxes and Polishes
Flash Point
1. SCOPE
1.1 This method describes three procedures for determining the flash point
of waxes, polishes and related materials.
1.2 The procedures outlined in par. 3.1 and 5.1 apply to liquids with a
kinematic viscosity below 5.5 mm²/s (Note 1) at 40°C, or below
9.5 mm²/s at 25°C, and a flash point below 93°C.
1.3 The procedure outlined in par. 4.1 applies to…
Methods of Sampling and Testing Waxes and Polishes
Slip Resistance
1. Scope
1.1 This test method covers the measurement of the static coefficient of
friction of floor surfaces for the James Machine. The apparatus is not
suitable for use on wet, rough, or corrugated surfaces. The apparatus is
suitable for laboratory testing.
1.2 This standard does not purport to address all of the safety problems, if
any, associated with its use. It is the…
Poly(Vinyl Chloride) Jacketing Sheet, for Insulated Pipes, Vessels and Round
Ducts
1. SCOPE
1.1 This standard applies to poly(vinyl chloride) (PVC) sheet used as
jacketing over insulated surfaces of vessels and round ducts, or
preformed jacketing for pipe elbows, tees, etc., where the surface
temperature is between -20°C and +65°C.
1.2 The testing and evaluation of a product against this standard may
require the use of materials and/or…
Methods of Testing Petroleum and Associated ProductsLow Temperature Flow Test (LTFT) for Diesel Fuel...
1. Scope
1.1 This method describes the procedure for determining the filter plugging
tendency of diesel fuels at low temperature due to the formation of wax
crystals.
1.2 The method applies to all distillate diesel fuels. Fuels passing this
test are expected to provide satisfactory fuel flow in automotive
equipment at temperatures equal to or…
Calcium Silicate Thermal Insulation for Piping, Machinery and Boilers
1. Scope
1.1 This standard specifies the performance requirements and test methods
for calcium silicate used as thermal insulation on piping, machinery
and boilers where the temperature of the hot surface is between 40 and
800°C.
1.2 The testing and evaluation of a product against this standard may
require the use of materials and/or equipment…