ANSI/CAN/UL/ULC 2447:2023

Scope 1.1 This Standard sets forth the minimum requirements for containment sumps, and associated sump fittings and accessories (products) intended for below-grade, or at-grade, or above-grade use as an enclosure for the housing of, and access to, underground piping, connector piping, and other fueling system components (such as pumps, valves, sensors, wiring, etc.), in addition to temporary containment of typical liquid fuels as identified in this Standard. These products are intended for use in commercial (public) or private (fleet) automotive fueling station applications or similar fuel dispensing applications, and in piping systems for fuel supply to generators, burners or similar equipment. Some sump fitting or sump accessory products may be optionally evaluated for repair or replacement applications in containment sumps that have been in service. 1.2 Containment sumps may be either primary or secondary constructions of metallic, nonmetallic or composite materials. Typical containment sump types are: a) Tank sumps – Sumps intended for installation above underground flammable and combustible liquid storage tanks; b) Dispenser sumps – Sumps intended for installation below flammable and combustible liquid dispensing equipment; c) Transition sumps – Sumps intended for access to liquid or vapour piping run manifolds, fittings and valves in a fueling system; and d) Fill/vent sumps – Sumps intended for housing of fill and/or vent pipe ends, drain valves, gauges or monitors connected to the tank. 1.3 Sump fittings may be included as either an integral part of the containment sump, or as a fieldinstalled kit, and may include but are not limited to the following sump applications: a) Penetration fittings – Fittings intended for sealing pipe penetrations through the sump wall; b) Termination fittings – Fittings intended for connecting pipe terminations at the sump wall; c) Internal fittings – Fittings intended for connection of working components inside the sump; and d) Test and monitor fittings – Fittings intended for periodic testing or continuous monitoring of the sump and/or pipe. 1.4 Sump accessories may be included as either an integral part of the containment sump, or as a fieldinstalled kit, and may include but are not limited to the following sump applications: a) Sump covers and sump lids – Covers or lids intended to limit access to the sump with structural and leak resistance features; b) Sump frames – Frames intended to provide structural support of the sump walls and/or components above or in the sump; c) Sump brackets – Brackets intended to provide structural attachment points for components inside the sump; and d) Chase pipes – Soil pipes intended to provide a structural conduit for routing underground carrier pipes for flammable and combustible liquids to and from the sump. 1.5 Containment sumps, fittings and accessories are intended for the containment of flammable and combustible liquids under the expected use conditions and exposures that have similar chemical, physical and material compatibility properties as represented in these requirements. Examples of these liquids include: a) Petroleum products, including petroleum hydrocarbon fuels with low-biofuels blends, and similar flammable or combustible liquid petroleum derivatives, such as fuel components (cetane, hexane, heptane), and oils (lubricating, hydraulic, machine); b) Oxygenated fuel blends, including all “petroleum product” liquids plus petroleum hydrocarbon fuels with low-biofuels blends; c) Oxygenates, including all “petroleum product” and “oxygenated fuel blends” liquids plus pure/denatured or highest oxygenated blend stocks for use in mixing of dispensed lower fuel blends and components, such as biodiesel and ethanol; and d) Other flammable and combustible liquids (for which the test fuels in Annex A are not considered to be sufficient or applicable) that can be demonstrated or determined to be compatible with the accessory materials as determined by the certifier. 1.6 Products covered by this Standard are intended to be installed and used in accordance with, but not limited to, any of the following documents: a) In Canada 1) National Fire Code of Canada, Part 4; 2) CSA B139 series, Installation code for oil-burning equipment; 3) CCME PN 1326, Environmental Code of Practice for Aboveground and Underground Storage Tank Systems Containing Petroleum and Allied Petroleum Products; and 4) Regulation of the authority having jurisdiction. b) In the United States 1) NFPA 30, Flammable and Combustible Liquids Code; 2) NFPA 30A, Code for Motor Fuel Dispensing Facilities and Garages; 3) NFPA 1, Fire Code; 4) International Fire Code published by the International Fire Council; or 5. Other Applicable Federal and State regulations for the specific product or application it is being utilized in. 1.7 These products are factory manufactured and intended for on-site field assembly, inspection and leak testing for the specified applications and use conditions by qualified persons in accordance with the manufacturer's instructions and local requirements. 1.8 These products are intended to be periodically inspected and maintained for continued service, or taken out of service if necessary by qualified persons in accordance with industry recommended practices and/or the manufacturer's instructions. 1.9 These products have not been evaluated for use after natural disasters, fires or exposures to chemicals not representative of the test liquids or excessive physical damage beyond the expected assembly, installation and uses as identified in these requirements. 1.10 These products have not been evaluated for special use applications where exposed to heavy or continuous physical abuses, excessive mechanical stresses; or environments that operate outside of the expected atmospheric conditions and ambient use temperature range. 1.11 These requirements do not cover underground piping products which are found in UL 971, Standard for Nonmetallic Underground Piping for Flammable Liquids, UL 971A, Outline for Investigation of Metallic Underground Piping for Flammable Liquids, or ULC-S679, Standard for Metallic and Nonmetallic Underground Piping for Flammable and Combustible Liquids. 1.12 These requirements do not cover connector or aboveground piping products which are found in UL/ULC 2039, Standard for Flexible Connector Piping for Flammable and Combustible Liquids, or UL/ULC 1369, Standard for Aboveground Piping for Flammable and Combustible Liquids. NOTE: Refer to Annex C for historic information about applicable standards. 1.13 These requirements do not cover tank accessories which are found in UL/ULC 2583, Standard for Fuel Tank Accessories for Flammable and Combustible Liquids. NOTE: Refer to Annex C for historic information about applicable standards. 1.14 These requirements do not cover floating docks, submerged, or shipboard marine applications.