Safety of household and similar electrical appliances - Part 2 - 40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
Scope:
This clause of Part 1 is replaced by the following.
This International Standard deals with the safety of electric HEAT PUMPS, including SANITARY HOT WATER HEAT PUMPS, AIR-CONDITIONERS, and DEHUMIDIFIERS incorporating motor-compressors and hydronic room FAN COILS, their maximum RATED VOLTAGES being not more than 250 V for single phase appliances and 600 V for all other appliances.
Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.
This standard also applies to electric HEAT PUMPS, AIR CONDITIONERS and DEHUMIDIFIERS containing FLAMMABLE REFRIGERANT. FLAMMABLE REFRIGERANTS are defined in 3.120.
The appliances referenced above may consist of one or more factory made assemblies. If provided in more than one assembly, the separate assemblies are to be used together, and the requirements are based on the use of matched assemblies.
NOTE 101 A definition of "motor-compressor" is given in IEC 60335-2-34, which includes the statement that the term motor-compressor is be used to designate either a hermetic motor-compressor or semi-hermetic motor-compressor.
NOTE 102 Requirements for refrigeration safety are covered by ISO 5149, and requirements for containers intended for storage of the heated water included in SANITARY HOT WATER HEAT PUMPS are, in addition, covered by IEC 60335-2-21.
This standard does not take into account chemicals other than group A1, A2, or A3 as defined by 3.121.
NOTE 103 This standard specifies particular requirements for the use of flammable refrigerants. Unless specifications are covered by this standard, including the annexes, requirements for refrigerating safety are covered by ISO 5149.
The sections and clauses in ISO 5149 of particular concern to this standard are as follows:
- Section 3: Design and construction of equipment applies to all appliances and systems.
- Section 4: Requirements for utilization applies to appliances and systems which are for "similar electrical appliances", i.e. commercial and light industrial.
- Section 5: Operating procedures applies to appliances and systems which are for "similar electrical appliances", i.e. commercial and light industrial.
SUPPLEMENTARY HEATERS, or a provision for their separate installation, are within the scope of this standard, but only heaters which are designed as a part of the appliance package, the controls being incorporated in the appliance.
NOTE 104 Attention is drawn to the fact that
- for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary;
- for appliances subjected to pressure, additional requirements may be necessary;
- in many countries additional requirements are specified, for example, by the national health authorities responsible for the protection of labour and the national authorities responsible for storage, transportation, building constructions and installations.
NOTE 105 This standard does not apply to
- humidifiers intended for use with heating and cooling equipment (IEC 60335-2-88);
- appliances designed exclusively for industrial processing;
- appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
1DV.1 DE Modification of Clause 1 of this Part 2 as follows:
Delete the 4th paragraph of Clause 1, Scope.
1DV.2 DE Modification of Clause 1 by adding NOTE 105A:
NOTE 105A Consistent with Clause 1DV.1, this standard is not intended to be used to evaluate products that employ flammable refrigerants. None of the flammable refrigerant related clauses apply. These include the flammability related requirements portions of Clause 7, Clause 22.113, Clause 22.114, Clause 22.115, Clause 22.116, Clause 22.117, Clause 22.118, Annex BB, Annex CC, Annex DD, Annex FF, and Annex GG
Project need:
Note: The information provided above was obtained by the Standards Council of Canada (SCC) and is provided as part of a centralized, transparent notification system for new standards development. The system allows SCC-accredited Standards Development Organizations (SDOs), and members of the public, to be informed of new work in Canadian standards development, and allows SCC-accredited SDOs to identify and resolve potential duplication of standards and effort.
Individual SDOs are responsible for the content and accuracy of the information presented here. The text is presented in the language in which it was provided to SCC.