Fixed inductors for electromagnetic interference suppression - Part 2-2: Blank detail specification ...
IEC 60938-2-2:1999 forms the basis for a uniform procedure for a common mark. It implements the approval schedule for safety tests only in IEC 60938-2, requires a declaration of design for parameters relevant to safety tests and prescribes conformance tests to be conducted on every lot prior to its release and re-qualification tests depending on changes of the design.
Fixed inductors for electromagnetic interference suppression - Part 2-2: Blank detail specification ...
IEC 60938-2-2:1999 forms the basis for a uniform procedure for a common mark. It implements the approval schedule for safety tests only in IEC 60938-2, requires a declaration of design for parameters relevant to safety tests and prescribes conformance tests to be conducted on every lot prior to its release and re-qualification tests depending on changes of the design.
1. Scope
1.1 Purpose
The purpose of this Code is to provide minimum requirements for the design,
construction, installation, and maintenance of those mechanical refrigeration
systems included in Clause 1.2, so as to minimize the risk of human injury.
Note: This Code does not directly address protection of property and
preservation of the environment, which may be addressed in other Acts…
1. SCOPE
1.1 This standard applies to interior latex semigloss paint suitable for
use on all interior walls, ceilings and trim, either new or previously painted.
1.2 The testing and evaluation of a product against this standard may
require the use of materials and/or equipment that could be hazardous. This
document does not purport to address all the safety aspects associated…
1. SCOPE
1.1 This standard applies to an air-drying flat alkyd enamel for use on
primed wooden and metal surfaces of equipment, particularly where a glare-free
finish is required and where mar resistance is not of prime importance.
1.2 The enamel can be used as an interior or exterior protective coating on
wooden surfaces and ferrous metal surfaces primed with primer conforming…
1. SCOPE
1.1 This standard applies to a pigmented cold-curing, two-component gloss
epoxy coating for use on properly prepared unpainted surfaces, such as
concrete, concrete blocks, brick and wood, and on primed metal.
1.2 The coating is intended for use on surfaces where good impact, superior
washability and good durability are required, for industrial applications where…
1. SCOPE
1.1 This standard applies to a solvent for use with vinyl pretreatment
coatings conforming to CAN/CGSB-1.213.
1.2 The solvent is intended primarily for cleaning equipment used in
applying vinyl preteatment coatings.
1.3 The testing and evaluation of a product against this standard may
require the use of materials and/or equipment that could be hazardous. This
document…
1. SCOPE
1.1 This standard applies to a high-solvency thinner for use with synthetic
resin finishes.
1.2 The thinner is suitable for the general thinning of synthetic resin
base finishes requiring a higher solvent power than provided by thinner
conforming to CAN/CGSB-1.4, but not as high as thinner conforming to
CAN/CGSB-1.94.
1.3 It is particularly suited for thinning materials by…
Chemical conversion coatings — Black oxide coating on iron and steel — Specification and test metho...
This International Standard specifies requirements for black oxide coatings on iron and steel (including cast and
wrought iron, carbon steel, low alloyed steel and stainless steel). Black oxide coatings can be used to diminish
friction between sliding or bearing surfaces or for decorative purposes or to reduce light reflection. Such coatings,
with or without supplementary preservative treatment,…
Animal feeding stuffs — Determination of fat content
This International Standard specifies a method for the determination of the fat content of animal feeding stuffs. The
method is applicable to animal feeding stuffs except oilseeds and oilseed residues.
For the purposes of this method, the following two categories of animal feeding stuffs are distinguished. Samples of
products in category B need a hydrolysis step prior to extraction.
Category B…