Information Technology - Telecommunications and Information Exchange Between Systems - Using ECMA-32...
This National Standard of Canada is equivalent to International Standard ISO/IEC TR 18057:2004.
1 Scope
Services for Computer Supported Telecommunications Applications are defined by Standard ECMA-269 and the XML Protocol for those services are defined by Standard ECMA-323.
In many cases, applications require only a small subset of the features standardized in CSTA. In a voice browser…
Paints and varnishes — Standard panels for testing
ISO 1514:2004 specifies several types of standard panel and describes procedures for their preparation prior to painting. These standard panels are for use in general methods of test for paints, varnishes and related products.
Complete filter units for radio interference suppression - Part 2-2: Blank detail specification - Pa...
IEC 60939-2-2:2004 forms the basis for a uniform procedure for a common Safety Mark. It implements the approval schedule for the safety test described in IEC 60939-2, requires a declaration of design for parameters relevant to safety and prescribes conformance tests to be conducted on every lot prior to its release and requalification tests depending on changes to the declared design.
Complete filter units for radio interference suppression - Part 2-2: Blank detail specification - Pa...
IEC 60939-2-2:2004 forms the basis for a uniform procedure for a common Safety Mark. It implements the approval schedule for the safety test described in IEC 60939-2, requires a declaration of design for parameters relevant to safety and prescribes conformance tests to be conducted on every lot prior to its release and requalification tests depending on changes to the declared design.
1. SCOPE
1.1 This standard applies to four grades of gasoline to which no lead or phosphorus compounds have been added. They
are intended for use in spark ignition engines under a wide range of climatic conditions.
1.2 Gasoline specified in this standard may contain methyl tertiary butyl ether (MTBE) or other aliphatic ethers.
1.3 Provincial and federal regulations control some parameters…
Textile Test Methods: Dimensional Change in Domestic Laundering of Textiles
1. PURPOSE AND SCOPE
1.1 This method determines the dimensional change of textile fabrics or garments, likely to occur in domestic
laundering procedures. The fabric specimen or garment is subjected to an appropriate combination of specified
washing, drying and restoration procedures.(1)
1.2 Seven washing, six drying and three restoration procedures are included as follows:
1.2.1…
Road vehicles — Detection of exhaust system leaks — Helium test method and detection device specific...
ISO 16247:2004 specifies a helium test method for detecting and localising gas leaks in the exhaust systems of road vehicles equipped with an internal combustion engine, in order to improve the quality of exhaust gas measurements. In doing so, it completes the requirements of ISO 3929, applicable regulations and, depending on the leak rate for detection, ISO 13556. The method is particularly…
Fixed capacitors for use in electronic equipment - Part 14-2: Blank detail specification - Fixed cap...
IEC 60384-14-2:2004 forms the basis for a uniform procedure for a common International Safety Mark. It implements the approval schedule for safety tests in IEC 60384-14, requires a declaration of design for parameters relevant to safety and prescribes conformance tests to be conducted on every lot prior to its release and requalification tests depending on changes to the declared design.
<br…
Fixed capacitors for use in electronic equipment - Part 14-3: Blank detail specification - Fixed cap...
forms the basis for a uniform procedure for a common International Safety Mark. It implements the approval schedule for safety tests in IEC 60384 14, requires a declaration of design for parameters relevant to safety and prescribes conformance tests to be conducted on every lot prior to its release and requalification tests depending on changes to the declared design.
Fixed capacitors for use in electronic equipment - Part 14-2: Blank detail specification - Fixed cap...
IEC 60384-14-2:2004 forms the basis for a uniform procedure for a common International Safety Mark. It implements the approval schedule for safety tests in IEC 60384-14, requires a declaration of design for parameters relevant to safety and prescribes conformance tests to be conducted on every lot prior to its release and requalification tests depending on changes to the declared design.
This…