In vitro diagnostic test systems — Requirements and recommendations for detection of severe acute re...
This document provides requirements and recommendations for the design, development, verification, validation and implementation of analytical tests for detecting the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) using nucleic acid amplification. It addresses pre-examination, examination and post-examination process steps for human specimens.
This document is applicable to medical…
Workplace air — Gases and vapours — Requirements for evaluation of measuring procedures using diffus...
This document specifies performance requirements and test methods under prescribed laboratory conditions for the evaluation of diffusive samplers (see Reference [1]) and of procedures using these samplers for the determination of gases and vapours in workplace atmospheres (see Reference [2]).
This document is applicable to diffusive samplers and measuring procedures using these samplers, such as…
Marine energy - Wave, tidal and other water current converters - Part 202: Early stage development o...
IEC TS 62600-202:2022 specifies the development stages of Tidal Energy Converters up to the pre-prototype scale (Stages 1 to 3). It includes the hydraulic laboratory test programs, where environmental conditions are controlled so they can be scheduled, and the first scaled system open-water trials, where combinations of tidal currents, wind and waves occur naturally and the programs are adjusted…
Mechanical vibration — Uncertainty of the measurement and evaluation of human exposure to vibration
This document specifies methods for determining the uncertainty of the measurement and evaluation of human exposure to vibration. It applies to measurements of vibration quantities (measurands), calculated following a relevant measurement model on the basis of directly measured values, to evaluate
a) human exposure to hand-transmitted vibration at the workplace,
b) vibration emission of hand-held…
Road vehicles — Light alloy wheels — Lateral impact test
This document specifies a laboratory test procedure to evaluate the axial (lateral) kerb impact collision properties of a wheel manufactured either wholly or partly of light alloys. It is intended for passenger car applications, and special vehicle applications where there is a possibility of the wheel impacting the kerb, with the purpose of screening and/or quality control of the wheel.
Laminate floor coverings — Determination of abrasion resistance
This document specifies two methods (A and B) for measuring abrasion of laminate floor covering elements. The tests described measure the ability of the surface layer to resist abrasive wear-through.
Abrasion according to method A is achieved by rotating a test specimen in contact with a pair of loaded cylindrical wheels covered with specified abrasive paper. The resistance to wear according to…
Laboratory resistors - Part 1: Laboratory DC resistors
IEC 60477-1:2022 applies to resistors intended for use as laboratory DC resistors (hereinafter referred to as "resistors") comprising standard resistors, single or multiple resistors of accuracy Classes 0,000 05 to 10 and single or multi-dial resistors of accuracy Classes 0,000 5 to 10.
This document does not apply to:
1) resistors which are intended for use solely as permanently…
Laboratory resistors - Part 2: Laboratory AC resistors
IEC 60477-2:2022 applies to resistors intended as laboratory AC resistors for use over a range of frequencies from DC up to a stated frequency which is not in excess of 1 MHz. Such resistors are hereinafter referred to as "AC resistors".
In addition to satisfying the requirements of IEC 60477-1, resistors satisfying the requirements of this document are designed to have a small…
Mechanical vibration — Laboratory method for evaluating vehicle seat vibration — Part 2: Application...
This document defines specifications covering laboratory tests for seats designed for passengers and crew in railway tractive and trailer vehicles.
It concerns tri-axial rectilinear vibration within the frequency range 0,5 Hz to 50 Hz. It specifies the input test vibration to be used at seat testing.
This document makes it possible to characterize, in the form of frequency response functions, the…
Paper, board, pulps and cellulosic nanomaterials — Determination of dry matter content by oven-dryin...
This document specifies an oven-drying method for the determination of the dry matter content in paper, board, pulp and cellulosic nanomaterials in solid form, which all can be produced from virgin and /or recycled materials.
It is also applicable to the determination of the dry matter content of paper and board for recycling.
The procedure is applicable to paper, board, and pulp and cellulosic…