Safety code for elevators and escalators (Bi-national standard, with ASME A17.1)
Scope
1.1.1 Equipment Covered by This Code
This Code covers the design, construction, operation, inspection, testing, maintenance, alteration, and repair of the following equipment and its associated parts, rooms, spaces, and hoistways, where located in or adjacent to a building or structure (see 1.2):
(a) hoisting and lowering mechanisms, equipped with a car, that move between two or…
Scope
1.1
This Standard covers welding requirements for carbon and low-alloy welded steel construction, with the exception of those types listed in Clause 1.2.
Requirements that are essentially common to all such structures are covered in Clauses 3 to 10, while provisions applying specifically to statically-loaded structures and to cyclically-loaded structures are included in Clauses 11 and…
Plugs, receptacles, and cable connectors of the pin and sleeve type (Bi-national standard, with UL 1...
Scope
1.1
This standard applies to pin and sleeve type plugs, receptacles, power inlets, and connectors, rated up to 800 amperes and up to 600 volts ac or dc, and which may include up to eight pilot contacts. These devices are intended to provide power from branch circuits, or are for direct connection to the branch circuit in accordance with the Canadian Electrical Code Part I (CEC), C22.1, and…
Scope
1.1
This Standard applies to single-phase and polyphase transformers of the dry type for supplying energy to power, heating, and lighting circuits and designed to be installed and used in accordance with the Canadian Electrical Code, Part I.
1.2
This Standard applies to multiwinding and autotransformers rated 72.5 kV class and less.
1.3
This Standard applies to transformers for…
Information technology - Small Computer System Interface (SCSI) - Part 333: SCSI Stream Commands - 3...
ISO/IEC 14776-333:2013(E) defines the command set extensions in order to facilitate operation of the sequential-access device type. It is implemented in conjunction with the requirements of the SCSI Architecture Model-4 (SAM-4) standard and the applicable clauses of the SCSI Primary Commands-4 (SPC-4) standard. It fully specifies the standard command set for the sequential-access device type.
Energy performance of buildings — Assessment of overall energy performance
ISO 16346:2013 defines the general procedures to assess the energy performance of buildings, including technical building systems, and defines the different types of ratings, and the building boundaries.
The purpose of ISO 16346:2013 is to
a) collate results from other International Standards that calculate energy use for specific services within a building,
b) account for energy generated…
Household and similar electrical appliances - Safety - Part 2-110: Particular requirements for comme...
IEC 60335-2-110:2013 deals with the safety of microwave appliances intended for commercial use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. Appliances covered by this standard incorporate an open-ended applicator (as example an overview is given in Figure 103) for treatment of the load. They are…
Electronic railway equipment - On board driving data recording system - Part 1: System specification
IEC 62625-1:2013 covers the specification of an on board driving data recording system for the purpose of recording data about the operation of the train. The data refers both to the driver behaviour and the on board systems behaviour to support systematic safety monitoring as a means of preventing incidents and accidents. The data is recorded in a way that is suitable for identifying cause and…
Universal serial bus interfaces for data and power - Part 1: Universal serial bus specification, rev...
IEC 62680-1:2013 defines an industry-standard USB. The specification describes the bus attributes, the protocol definition, types of transactions, bus management, and the programming interface required to design and build systems and peripherals that are compliant with this standard. The text of this standard is based on documents prepared by the USB Implementers Forum (USB-IF). The structure and…
Photometric performance of roadway and street lighting luminaires
1.1
This Standard specifies photometric performance requirements for luminaires that are used for roadway
and street lighting applications.
1.2
The following light sources are addressed in this Standard:
a) clear HPS lamp;
b) clear metal halide lamp;
c) induction; and
d) LED.
Note: Future editions of this Standard might include other light sources, such as plasma.
1.3
This Standard is…