LED modules for general lighting — Safety specifications
1 Scope
[Replace this clause with the following]
1.1
This Standard specifies general and safety requirements for
(a) light-emitting diode (LED) modules without integral controlgear for operation under constant
voltage, constant current, or constant power; and
(b) self-ballasted LED modules with integral controlgear for use on dc supplies up to 250 V or ac supplies
up to 347 V.
1.2
This…
Standard Method of Fire Tests for Air Filter Units
1 SCOPE
1.1 These requirements cover air filter units of both washable and throw-away types for removal of dust
and other airborne particles from air circulated mechanically in equipment and systems.
Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t"
IEC 60079-31:2013 is applicable to electrical equipment protected by enclosure and surface temperature limitation for use in explosive dust atmospheres. It specifies requirements for design, construction and testing of electrical equipment and Ex Components. This standard supplements and modifies the general requirements of IEC 60079-0. Where a requirement of this standard conflicts with a…
Medical electrical equipment - Part 1-10: General requirements forbasic safety and essential perform...
IEC 60601-1-10:2007+A1:2013 Specifies requirements for the development (analysis, design, verification and validation) of a physiologic closed-loop controller (PCLC) as part of a physiologic closed-loop control system (PCLCS) in medical electrical equipment and medical electrical systems to control a physiologic variable. This collateral standard applies to various types of PCLC, e.g. linear and…
IEC 62230:2006+A1:2013 The spark-test method specified in this standard is intended for the detection of defects in the insulation or sheathing layers of electric cables. For single core cables with no outer metallic layer, the general process is accepted as being equivalent to subjecting samples of those cables to a voltage test in water. This standard specifies the operational requirements for…
Information technology — Software asset management — Part 5: Overview and vocabulary
ISO/IEC 19770-5:2013 provides an overview of Software Asset Management (SAM), which is the subject of the ISO/IEC 19770 family of standards, and defines related terms.
ISO/IEC 19770-5:2013 contains:
an overview of the ISO/IEC 19770 family of standards;
an introduction to SAM;
a brief description of the foundation principles and approaches on which SAM is based; and
consistent terms and…
Information technology - Software asset management - Part 5: Overview and vocabulary
ISO/IEC 19770-5:2013 provides an overview of Software Asset Management (SAM), which is the subject of the ISO/IEC 19770 family of standards, and defines related terms.
ISO/IEC 19770-5:2013 contains:
an overview of the ISO/IEC 19770 family of standards;
an introduction to SAM;
a brief description of the foundation principles and approaches on which SAM is based; and
consistent terms and…
Automatic electrical controls - Part 1: General requirements
IEC 60730-1:2013 applies to automatic electrical controls for use in, on, or in association with equipment for household and similar use. The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof. This standard is applicable to controls for building automation within the scope of ISO 16484. This standard also applies to automatic electrical…
Paints and varnishes — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-a...
ISO 16474-4:2013 specifies methods for exposing specimens to open-flame carbon-arc lamps in the presence of moisture to reproduce the weathering effects that occur when materials are exposed in actual end-use environments to daylight or to daylight filtered through window glass.
The specimens are exposed to filtered open-flame carbon-arc light under controlled conditions (temperature, humidity…
Paints and varnishes — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO 16474-2:2013 specifies methods for exposing specimens to xenon-arc light in the presence of moisture to reproduce the weathering effects that occur when materials are exposed in actual end-use environments to daylight or to daylight filtered through window glass.
The specimens are exposed to filtered xenon-arc light under controlled conditions (temperature, humidity and/or wetting). Various…
