1 Scope
1.1
This performance Standard applies to circular precast concrete pipe, manhole (maintenance hole)
sections, and accessories intended for
(a) use as sewer pipe for the conveyance of sewage, industrial wastes, and storm water; and
(b) the construction of culverts.
1.2
This Standard describes the following procedures for testing circular precast concrete pipe, manhole
sections, and…
1 Scope
1.1
This Standard specifies minimum requirements for masonry materials and masonry construction.
Notes:
1) Requirements for structural design of masonry are specified in CSA S304.
2) If a requirement specified in Part 9 of the National Building Code of Canada differs from a requirement
specified in this Standard, the requirement specified in this Standard should be followed.
3) General…
1 Scope
1.1 General
This Standard specifies requirements, in accordance with the National Building Code of Canada, for the design and strength evaluation of
a)
structures of reinforced and prestressed concrete;
b)
plain concrete elements; and
c)
special structures such as parking structures, arches, tanks, reservoirs, bins and silos, towers, water towers, blast-resistant structures, and…
1.1
This Standard applies to motor-operated liquid pump units for use in nonhazardous, indoor, outdoor
(exposed), and submerged locations and designed to be used in accordance with the Rules of the
Canadian Electrical Code, Part I.
1.2
This Standard applies to
a) pumps for either permanent or cord-connection to the source of supply;
b) cord- and plug-connected pumps; and
c) component-type…
Power consumption of small network equipment (SNE)
1.1
This Standard specifies the test method for measuring and reporting the power consumption of small
network equipment.
Note: This Standard is technology neutral.
1.2
The following products are not covered by this Standard:
a) network equipment capable of accepting interchangeable modules, such as line cards or additional
power supplies;
b) network equipment with one or more network ports using…
Standard for energy performance compliance, verification, and ratings of fuel-burning appliances and...
1.1
This Standard specifies criteria and methods to establish and verify the energy performance ratings for
fuel-burning appliances and equipment. This Standard includes procedures for sampling, analysis of test
results, and reporting.
1.2
This Standard applies , but is not limited, to the fuel-burning appliances listed in Table 1 and described in
Clause 14 that are tested in accordance…
1.1
This Standard applies to newly produced gas-fired outdoor infrared patio heaters (see Clause 3,
Definitions) hereinafter referred to as heaters or appliances, constructed entirely of new, unused parts
and materials.
Patio heaters are for use with:
a) natural gas; and
b) liquefied petroleum (propane) gases.
1.2
The heaters covered by this Standard are intended for installation in and…
Gas hose connectors for portable outdoor gas-fired appliances
1.1
This Standard applies to gas hose connectors (See Clause 3 Definitions), hereinafter referred to as
connectors. They are conduits for conveying gas and depend for gas-tightness on the wall structure of
the hose material. Such connectors shall be:
a) newly produced and constructed entirely of new, unused parts and materials; and
b) equipped with a fitting at each end provided with…
Characterization of the performance of illuminance meters and luminance meters
ISO/CIE 19476:2014 is applicable to illuminance and luminance meters. It defines quality indices characterizing the performance of such devices in a general lighting measurement situation, as well as measurement procedures for the individual indices and standard calibration conditions.
Measurements of illuminance or luminance and their accuracy are influenced by various parameters, such as…
Fibre optic active components and devices - Performance standards - Part 2: 850 nm discrete vertical...
IEC 62149-2:2014 covers the performance specification for 850-nm discrete vertical cavity surface emitting laser (VCSEL) devices of transverse multimode types used for fibre optic telecommunication and optical data transmission applications. The performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly…
