1.1
This Standard applies to all types of laboratory fume hoods, except for ductless fume hoods.
Note: Ductless fume hoods should not be considered acceptable substitutes for ducted fume hoods. Some
jurisdictions prohibit use of ductless fume hoods with certain chemicals. For these reasons, ductless fume hoods
have not been included in this Standard.
1.2
This Standard specifies
a) safety…
1.1
This Standard specifies requirements for the packaging, collection, handling, storage, and on-site treatment and disposal of health care waste materials.
1.2
1.2.1
This Standard applies to health care and veterinary–related waste, and health care–related waste generated in non-traditional health care settings.
1.2.2
“Health care and veterinary” refers to
a)
health care facilities and…
1.1
This Standard applies to assemblies of resistors, enclosures, and other components that provide high impedance grounding for the purpose of controlling the ground fault current or the voltage to ground of an alternating current system, when installed in accordance with the Canadian Electrical Code, Part I.
1.2
This Standard applies to neutral grounding resistor assemblies rated for use on…
1.1
This Standard specifies requirements for the design and performance of complete active fall-protection systems, including travel-restraint and vertical and horizontal fall-arrest systems. This Standard is intended for engineers with expertise in designing fall-protection systems.
1.2
This Standard does not specify design or performance requirements for fall-arrest equipment or systems that…
1.1
The CSA O80 Series of Standards specifies requirements related to the preservation and fire retardance
of wood through chemical treatment (pressure and thermal impregnation). The subjects covered
include materials and their analysis, pressure and thermal impregnation procedures, and fabrication and
installation to put treated wood into service.
1.2
This Standard lists reference…
1.1
This Standard applies to newly produced gas appliance connectors, constructed entirely of new unused
parts and materials, having nominal internal diameters of 1/4, 3/8, 1/2, 5/8, 3/4, and 1 in, and having
fittings at both ends provided with taper pipe threads for connection to a gas appliance and to house
piping. This Standard covers assembled appliance connectors not exceeding a nominal…
1.1
This Standard applies to gas convenience outlets (see Clause 3, Definitions), hereinafter referred to as
gas outlets and optional enclosures, not to exceed 1-1/2 in (38.1 mm) and pressures not to exceed 5 psi
(34.5 kPa), capable of operation at temperatures between 32°F and 200°F (0°C and 93.3°C) if intended
for indoor use only, or between -20°F and 200°F (-28.8°C and 93.3°C) if intended…
1.1
This Standard applies to cord-connected equipment rated 250 V and less, single phase, to be operated from branch circuits fused at not more than 30 amperes and intended for use indoors, in ordinary locations in accordance with the Canadian Electrical Code, Part I.
1.2
This Standard applies to equipment designed to remove water from the air in a room in which it operates, by condensing water…
1.1
This Standard applies to voltage and polarity testers for use in nonhazardous locations, in accordance
with the Rules of the Canadian Electrical Code, Part I, on electrical supply circuits and equipment at
points where the voltage difference does not exceed 750 V.
1.2
This Standard does not apply to devices primarily intended to measure voltage, such as those that
employ a meter…
Testing of three-phase synchronous machines during refurbishment
1.1
This Standard covers three-phase, alternating current, salient pole synchronous machines 150 kW and up, 200 through 13,800 volts, 60 and 50 Hertz and will assist in verifying the machine efficiency has been maintained.
Note: This Standard can be useful and applied with discretion to products outside the scope of this Standard.
1.2
Large 2-pole and 4-pole solid cylindrical rotor machines,…
