Installation code for propane fuel systems and containers on motor vehicles
1 Scope
1.1
This Code applies to
a)
the installation, servicing, and repair of propane fuel system components and containers on motor vehicles for the provision of motive power; and
b)
the installation of containers on motor vehicles such as recreational vehicles, outdoor food service units, and wash-mobiles when propane is to be used for fuel purposes (other than motive power).
Note: “…
1 Scope
1.1
This Standard applies to decorative lighting strings, decorative lighting outfits, pre-lit trees, and accessories, intended for seasonal or commercial use connected to circuits of 120 V nominal or less by means of an attachment plug, and designed to be used in accordance with the rules of the Canadian Electrical Code, Part I, in non-hazardous locations.
1.2
These requirements…
1 Scope
1.1
This Standard applies to
a)
electrostatic air cleaners intended to remove dust and dirt from the air and intended for general indoor residential and commercial use;
b)
air ionizer type air cleaners;
c)
other similar ionizing equipment; and
d)
duct-mounted type electrostatic air cleaners, air ionizers, and other similar ionizing equipment intended for general indoor…
Interconnection of distributed energy resources and electricity supply systems
1 Scope
1.1
This Standard specifies the technical requirements for the interconnection of distributed energy
resources (DER) and distribution systems up to 50 kV line to line at the point of common coupling (PCC).
1.2
This Standard does not define the maximum DER capacity or the upper voltage limit for installations
that are interconnected with a single PCC or connected to a given feeder.…
1 Scope
1.1 Purpose
The purpose of this Standard is to establish criteria for the design, manufacture, testing, inspection, installation, maintenance, use, and operation of vehicle-mounted aerial devices installed on a chassis, primarily used to position personnel, and for the training of operators for that equipment, to achieve the following objectives:
a)
prevention of personal injuries and…
Petroleum and natural gas industries — Specific requirements for offshore structures — Part 2: Seism...
1 Scope
This document contains requirements for defining the seismic design procedures and criteria for
offshore structures; guidance on the requirements is included in Annex A. The requirements focus on
fixed steel offshore structures and fixed concrete offshore structures. The effects of seismic events on
floating structures and partially buoyant structures are briefly discussed. The site-…
Petroleum and natural gas industries — Floating offshore structures — Part 1: Ship-shaped, semi-subm...
1 Scope
This document provides requirements and guidance for the structural design and/or assessment of
floating offshore platforms used by the petroleum and natural gas industries to support the following
functions:
— production;
— storage and/or offloading;
— drilling and production;
— production, storage and offloading;
— drilling, production, storage and offloading.
NOTE 1 Floating…
Kraft lignin — Glass transition temperature by differential scanning calorimetry
1 Scope
1.1
This Standard describes a method for the determination of the glass transition temperature (Tg) of kraft lignin. The procedure utilizes differential scanning calorimetry (DSC).
This procedure is applicable to solid lignins (e.g., powdered form) isolated from the kraft pulping process.
It does not apply to raw black liquor and lignin in the sodium form produced from the kraft…
Kraft lignin — Determination of thermal stability by thermogravimetry
1 Scope
1.1
This Standard describes the thermal analysis of kraft lignin using thermogravimetric methods.
Thermogravimetry can be used to determine the initial decomposition temperature(s), rate(s) of
decomposition, and the temperature at maximum decomposition of various materials, including lignins
at atmospheric pressure. All these temperatures are solely based on the mass loss and are not…
1 Scope
1.1 General
This Standard specifies testing and labelling requirements for hip protectors used to reduce the risk of hip fracture in the event of a fall.
Annex A provides a test method for measuring the effect of a hip protector in reducing the force to the proximal femur during a simulated fall. The test method is applicable both to hip protectors that are designed to withstand a…