Analogue audio disk records and reproducing equipment
IEC 60098:2020 applies to analogue audio disk records and the corresponding professional and domestic reproducing equipment. It excludes amplifiers and loudspeakers, methods of measurement for which can be found in IEC 60268-3, IEC 60268-5, IEC 6026821 and IEC 60268-22.<br />
IEC 60098:2020 specifies the characteristics that are necessary to ensure compatibility between analogue audio disk…
IEC 61322:2020 applies to installed dose equivalent rate meters, warning assemblies and monitors, as defined below. It covers equipment intended to measure neutron radiation in dose equivalent rates in the energy region between thermal and 20 MeV for the purposes of radiation protection.
Assemblies of this type are commonly defined as area radiation monitors. They are normally employed to…
Power systems management and associated information exchange - Data and communications security - Pa...
IEC 62351-100-3:2020, which is a technical specification, describes test cases of data and communication security for telecontrol equipment, Substation Automation Systems [SAS] and telecontrol systems, including front-end functions of SCADA.
The goal of this document is to enable interoperability by providing a standard method of testing protocol implementations to verify that a device fulfils…
Analogue audio disk records and reproducing equipment
IEC 60098:2020 applies to analogue audio disk records and the corresponding professional and domestic reproducing equipment. It excludes amplifiers and loudspeakers, methods of measurement for which can be found in IEC 60268-3, IEC 60268-5, IEC 6026821 and IEC 60268-22.
IEC 60098:2020 specifies the characteristics that are necessary to ensure compatibility between analogue audio disk records…
Air cargo equipment — Restraint straps — Part 2: Utilization requirements and recommendations and la...
This document aims at providing general utilization requirements and recommendations and calculation methods adequate to guarantee the effectiveness and ultimate load strength of tie-down/lashing arrangements performed to restrain cargo on board civil transport aircraft during flight:
a) cargo loaded and tied down onto airworthiness approved air cargo pallets, themselves restrained into…
Fuel cell technologies - Part 8-201: Energy storage systems using fuel cell modules in reverse mode ...
IEC 62282-8-201:2020 defines the evaluation methods of typical performances for electric energy storage systems using hydrogen. This is applicable to the systems that use electrochemical reaction devices for both power charge and discharge. This document applies to systems that are designed and used for service and operation in stationary locations (indoor and outdoor).
The conceptual…
Information technology - Fibre channel - Part 226: Single-byte command code sets mapping protocol - ...
This standard describes a communication interface between a channel and I/O control units that utilize the Single-Byte Command Code Sets (SBCCS) as implemented in a wide range of data processing systems. It employs information formats and signaling protocols that provide a uniform means for communicating with various types of I/O control units, facilitating a high bandwidth, high performance, and…
Geographic information — Geography Markup Language (GML) — Part 1: Fundamentals
The Geography Markup Language (GML) is an XML encoding in accordance with ISO 19118 for the transport and storage of geographic information modelled in accordance with the conceptual modelling framework used in the ISO 19100 series of International Standards and including both the spatial and non-spatial properties of geographic features.
This document defines the XML Schema syntax, mechanisms…
Information technology — Fibre channel — Part 226: Single-byte command code sets mapping protocol - ...
This standard describes a communication interface between a channel and I/O control units that utilize the Single-Byte Command Code Sets (SBCCS) as implemented in a wide range of data processing systems. It employs information formats and signaling protocols that provide a uniform means for communicating with various types of I/O control units, facilitating a high bandwidth, high performance, and…
Health informatics — Categorial structure for Chinese materia medica products manufacturing process
This document specifies the whole manufacturing process of Chinese materia medica products by defining a set of domain constraints of sanctioned characteristics, each composed of a relationship and an applicable categorial structure. It includes three process categories: processing, extracting and preparation.
This document is not applicable to Japanese traditional KAMPO medicinal products.