Interior air of road vehicles — Part 10: Whole vehicle test chamber — Specification and methods for ...
This document describes and specifies the whole vehicle test chamber, the vapour sampling assembly and the operating conditions for the determination of volatile organic compounds (VOCs; for more information see Annex E), and carbonyl compounds in vehicle cabin air. There are three measurements performed: one (for VOCs and carbonyl compounds) during the simulation of ambient conditions (ambient…
Precision Clock Synchronization Protocol for Networked Measurement and Control Systems
IEC 61588:2021 defines a network protocol, the Precision Time Protocol (PTP), enabling accurate and precise synchronization of the real-time clocks of devices in networked distributed systems. The protocol is applicable to systems where devices communicate via networks, including Ethernet. The standard allows multicast communication, unicast communication or both. The standard specifies…
Information technology — Radio frequency identification for item management — Part 1: Interference r...
This document defines a test method to evaluate the interference rejection performance of tags covered by ISO/IEC 18000-63 and a heterogeneous wireless system using different access technologies, e.g. radio frequency identification and cell phone network.
It specifies the general requirements and test requirements.
The test method in this document makes it possible to compare the relative…
Information technology - Radio frequency identification for item management - Part 1: Interference r...
This document defines a test method to evaluate the interference rejection performance of tags covered by ISO/IEC 18000-63 and a heterogeneous wireless system using different access technologies, e.g. radio frequency identification and cell phone network.
It specifies the general requirements and test requirements.
The test method in this document makes it possible to compare the relative…
Household and similar electrical appliances — Safety — Part 2-67: Particular requirements for floor ...
1 Scope
This clause of Part 1 is replaced by the following.
This International Standard deals with the safety of powered floor treatment machines intended for
commercial indoor or outdoor use for the following applications:
– scrubbing,
– wet or dry pick-up,
– polishing and dry buffing,
– application of wax, sealing products and powder based detergents,
– shampooing,
– stripping,…
Household and similar electrical appliances — Safety — Part 2-72: Particular requirements for floor ...
1 Scope
This clause of Part 1 is replaced by the following.
This International Standard deals with the safety of powered ride-on and powered WALK-BEHIND MACHINES
intended for commercial indoor or outdoor use for the following applications:
– sweeping,
– scrubbing,
– wet or dry pick-up,
– polishing,
– application of wax, sealing products and powder based detergents,
– shampooing
of…
Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 12: Rigid fuel line in cop...
This document specifies tests and requirements for the rigid fuel line in copper and its alloys, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following:
a) fuel containers;
b) stationary gas engines;
c) container mounting hardware;
d) electronic fuel management;
e) refuelling receptacles.…
Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 13: Tank pressure control ...
This document specifies tests and requirements for the tank pressure control regulator, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833.
This document is not applicable to the following:
a) fuel containers;
b) stationary gas engines;
c) container mounting hardware;
d) electronic fuel management;
e) refuelling receptacles.
It is…
Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 11: Fittings
This document specifies tests and requirements for the fittings, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833.
This document is not applicable to the following:
a) fuel containers;
b) stationary gas engines;
c) container mounting hardware;
d) electronic fuel management;
e) refuelling receptacles.
It is recognized that…
Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 9: Gas-tight housing and v...
This document specifies tests and requirements for the gas-tight housing and ventilation hose, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833.
This document is applicable to vehicles using natural gas in accordance with ISO 15403-1 (mono-fuel, bi-fuel, or dual-fuel applications). It is not applicable to the following:
a) fuel…